- Posted by alex@engineeredsource.com
- On September 12, 2019
- 0 Comments
These custom precision steel pins were manufactured domestically for our customer involved in water treatment product manufacturing. 1018 CRS material was used with plain finish. The drive-less head measures .060″ in height and .290″ for the diameter, +/-.005″. The shoulder portion was the most critical with a diameter of .195″ +/- .001″ and a slight […]
Read More
- Posted by alex@engineeredsource.com
- On September 10, 2019
- 0 Comments
Production of these custom internally & externally threaded studs was run at approximately 10,000 pieces, in medium carbon grade 5 equivalent steel material. The specific hardness requirement was set to 25-35 HRC. The custom threaded studs had an overall length of .75″ +/.02″ with a 45-50 degree tapered point on one side. Slotted drives were […]
Read More
- Posted by alex@engineeredsource.com
- On September 3, 2019
- 0 Comments
These custom flange nuts were manufactured domestically using 17-4PH stainless steel material with 10-24 internal thread. Overall height of the flange nut was .19″ +/-.01″ and the diameter of the flange was a critical dimension at .330″ +.000/-.015″. The hex was set to .250″ +.000/-.005″ across the flats. Our internal part number is NRNS-10-117-4 and […]
Read More
- Posted by alex@engineeredsource.com
- On August 30, 2019
- 0 Comments
These custom binding posts were manufactured using 316 stainless steel material, with 3/8 coarse internal thread tapped as close to the head as possible and a T30 drive cold headed all the way through. The head diameter is 1.13″ head height at .19″ +/- .01″. The shoulder outside diameter is set to .63″ and measures […]
Read More
- Posted by alex@engineeredsource.com
- On August 28, 2019
- 0 Comments
These custom low head slotted machine screws were manufactured domestically using 12L14 steel material and then run through a commercial black oxide process. Length under the head was set at .375″ +/-.03″, fully threaded with 8-32 thread pitch. The head height was set at .055″, diameter at .265″, slot width at .05″, and slot depth […]
Read More
- Posted by alex@engineeredsource.com
- On August 8, 2019
- 0 Comments
We supply these custom aerospace compression springs to our aerospace components manufacturing customer. 17-7PH stainless steel material is used for the domestic production of these parts, per AMS 5673-F. Our production runs are typically in the smaller 500 piece quantity range for this specific spring, with lead time at 8-10 weeks. That lead time includes […]
Read More
- Posted by alex@engineeredsource.com
- On August 7, 2019
- 0 Comments
These custom precision flange bushings were produced domestically in the USA using 18-8 stainless steel material. The overall length measured .630″ +/-.01″ and the part incorporated both an external flange and an external flange per customer supplied drawings. The OD on the barrel portion is .5″ and .585″ at the external flange, both with the […]
Read More
- Posted by alex@engineeredsource.com
- On July 19, 2019
- 0 Comments
These are tiered custom threaded stainless pins created for an audio equipment manufacturer in 18-8 stainless steel material. Production was done domestically with a lead time of 5-6 weeks from order. The overall length of the part is at 1.4″ inclusive of .90″ of M3 coarse thread and .37″ of 10-32 thread. Multiple shoulder steps […]
Read More
- Posted by alex@engineeredsource.com
- On July 10, 2019
- 0 Comments
We supplied these custom low head socket cap screws in alloy steel material with black oxide finish. Two different lengths were required by our customer – 28MM and 33MM under the head. We used COTS version of this DIN7984 socket cap screw at 35MM as the base part, then cutting and chamfering the parts to […]
Read More
- Posted by alex@engineeredsource.com
- On July 10, 2019
- 0 Comments
We supplied 54 pieces of these custom aerospace socket head cap screws to our long time customer. They were made in the USA using 18-8 stainless steel material (no DFARS requirement on these) with a broached 9/64″ hex socket drive with min .077″ engagement depth. 1″ of the overall 4.25″ length under the head was […]
Read More
